Search Results

Commercial three way catalysts have limited capacity towards reducing NOx in the presence of excessive oxygen. This prevents lean-burn combustion concepts from meeting legislative emission standards. A solution towards decreasing NOx emissions in the presence of excess air is the use of a passive-SCR system. Under rich conditions ammonia is formed over an ammonia formation catalyst, the ammonia is stored in the SCR and in its turn reacts with the NOx under lean engine conditions. Here up-scaled Pt/Al2O3 and Pd/Al2O3 catalysts as well as a commercially Pd-Rh based three-way catalyst (TWC) are evaluated using both engine and further lab-scale tests. The purpose of these tests is to compare the ammonia production for the various catalysts under various lambda values and temperatures by means of engine and lab scale tests. The Pd/Al2O3 showed little sensitivity to temperature both under engine and lab scale experiments.

Studies have shown that premixed combustion concepts such as PCCI and RCCI can achieve high efficiencies while maintaining low NOx and soot emissions. The RCCI (Reactivity Controlled Compression Ignition) concept use blending port-injected high-octane fuel with early direct injected high-cetane fuel to control auto-ignition. This paper describes studies on RCCI combustion using CNG and diesel as the high-octane and high-cetane fuels, respectively. The test was conducted on a heavy-duty single cylinder engine. The influence of injection timing and duration of the diesel injections was examined at 9 bar BMEP and1200 rpm. In addition, experiments were conducted using two different compression ratios, (14 and 17) with different loads and engine speeds. Results show both low NOx and almost zero soot emissions can be achieved but at the expense of increasing of unburned hydrocarbon emissions which could potentially be removed by catalytic after-treatment.

Hydrotreated vegetable oil (HVO) is a renewable high quality paraffinic diesel that can be obtained by the hydrotreating of a wide range of biomass feedstocks, including vegetable oils, animal fats, waste oils, greases and algal oils. HVO can be used as a drop-in fuel with beneficial effects for the engine and the environment. The main objective of this study was to explore the potential of HVO as a candidate bio blendstock for new experimental formulations of diesel fuel to be used in advanced combustion systems at different compression ratios and at high EGR rates in order to conform to the Euro 6 NOx emission standard. The experiments were carried out in a single-cylinder research engine at three steady-state operating conditions and at three compression ratios (CR) by changing the piston.

In this paper the characteristics of a mixture of glycerol-based ethers usable in a compression ignition engine are investigated, in terms of efficiency and emissions. Alternative pathways for the energetic exploitation of biodiesel derived glycerol became of increasing interest as the biodiesel production was increased worldwide. Because of its detrimental physical and chemical properties, raw glycerol is hardly usable in conventional internal combustion engines (ICE). However, etherification of glycerol with tert-butyl alcohol and isobutylene allows obtaining a mixture mainly composed of higher glycerol ethers (GEM) suitable for compression ignition engines. Thus, the aim of this research study was to test a mixture of mono-, di- and tri-tert-butyl ethers of glycerol in blend with a commercial diesel fuel in a compression ignition engine, evaluating the fuel efficiency and the impact on the pollutant emissions.

The EU emission standards for new rail Diesel engines are becoming even more stringent. EGR and SCR technologies can both be used to reduce NOx emissions; however, the use of EGR is usually accompanied by an increase in PM emissions and may require a DPF. On the other hand, the use of SCR requires on-board storage of urea. Thus, it is necessary to study these trade-offs in order to understand how these technologies can best be used in rail applications to meet new emission standards. The present study assesses the application of these technologies in Diesel railcars on a quantitative basis using one and three dimensional numerical simulation tools. In particular, the study considers a 560 kW railcar engine with the use of either EGR or SCR based solutions for NOx reduction. The NOx and PM emissions performances are evaluated over the C1 homologation cycle.

Nowadays, alcoholic fuels gain increased interest as alternative transportation biofuel even in compression ignition engines due to the fact that they contain oxygen and can be produced in a sustainable way. Furthermore, due to their lower CN (Cetane Number) they suit better for premixed combustion applications. Experimental research was conducted on a single cylinder engine provided with modern engine architecture modified for DF (Dual-Fuel) purposes. The authors have investigated the use of ethanol in a DF engine in order to exploit its well-known advantages in premixed combustion mode. The DF approach appears to be a promising solution because it permits flexible control of the premixed fuel fraction regardless from the operating conditions. This improves the exploitation of the ethanol potential according the engine working conditions.

A regular flex-fuel engine can operate on any blend of fuel between pure gasoline and E85. Flex-fuel engines have relatively low efficiency on E85 because the hardware is optimized for gasoline. If instead the engine is optimized for neat ethanol, the efficiency may be much higher, as demonstrated in this paper. The studied two-liter engine was modified with a much higher compression ratio than suitable for gasoline, two-stage turbocharging and direct injection with piezo-actuated outwards-opening injectors, a stratified combustion system and custom in-house control system. The research engine exhibited a wide-open throttle performance similar to that of a naturally aspirated v8, while offering a part-load efficiency comparable to a state-of-the-art two-liter naturally aspirated engine. NOx will be handled by a lean NOx trap. Combustion characteristics were compared between gasoline and neat ethanol.

In order to avoid the high CO and HC emissions associated with low temperature when using high levels of EGR, partially premixed combustion is an interesting possibility. One way to achieve this combustion mode is to increase the ignition delay by adjusting the inlet valve closing timing, and thus the effective compression ratio. The purpose of this study was to investigate experimentally the possibilities of using late and early inlet valve closure to reduce NOx emissions without increasing emissions of soot or unburned hydrocarbons, or fuel consumption. The effect of increasing the swirl number (from 0.2 to 2.5) was also investigated. The combustion timing (CA50) was kept constant by adjusting the start of injection and the possibilities of optimizing combustion using EGR and high injection pressures were investigated. Furthermore, the airflow was kept constant for a given EGR level.

The development of high efficiency powertrains is a key objective for car manufacturers. One approach for improving the efficiency of gasoline engines is based on homogeneous charge compression ignition, HCCI, which provides higher efficiency than conventional strategies. However, HCCI is only currently viable at relatively low loads, primarily because at high loads it involves rapid combustion that generates pressure oscillations in the cylinder (ringing), and partly because it gives rise to relatively high NOX emissions. This paper describes studies aimed at increasing the viability of HCCI combustion at higher loads by using fully flexible valve trains, direct injection with charge stratification (SCCI), and intake air boosting. These approaches were complemented by using EGR to control NOX emissions by stoichiometric operation, which enables the use of a three-way catalyst.

When using dimethyl ether (DME) to fuel diesel engines at high load and speed, applying high amounts of exhaust gas recirculation (EGR) to limit NOX emissions, carbon monoxide (CO) emissions are generally high. To address this issue, the combustion and emission processes in such engines were analyzed with the three-dimensional CFD KIVA3V code. The combustion sub-mechanism (76 species and 375 reactions) was validated by comparing simulated ignition delays and flame velocities to reference data under diesel-like and atmospheric conditions, respectively. In addition, simulated and experimentally determined rate of heat release (RoHR) curves and emission data were compared for a heavy-duty single-cylinder DME engine (displaced volume, 2.02 liters) with DME-adapted piston and nozzle geometries. The simulated RoHR curves captured the main features of the experimentally measured curves, but deviated in the premixed (higher peak) and late combustion phases (too high).

This paper illustrates the results of an experimental study on the impact of a low cetane number (CN) oxygenated fuel on the combustion process and emissions of a light-duty (LD) single-cylinder research engine. In an earlier study, it was concluded that cyclic oxygenates consistently outperformed their straight and branched counterparts at equal oxygen content and with respect to lowering soot emissions. A clear correlation was reported linking soot and CN, with lower CN fuels leading to more favorable soot levels. It was concluded that a lower CN fuel, when realized by adding low reactive cyclic oxygenates to commercial diesel fuel, manifests in longer ignition delays and thus more premixing. Ultimately, a higher degree of premixing, in turn, was thought to suppress soot formation rates.

The goal of this paper is to acquire insight into the influence of cetane number (CN) and fuel oxygen on overall engine performance in the Premixed Charge Compression Ignition (PCCI) combustion mode. From literature, it is known that low reactive (i.e., low CN) fuels increase the ignition delay (ID) and therefore the degree of mixing prior to auto-ignition. With respect to fuel oxygen, it is known that this has a favorable impact on soot emissions by means of carbon sequestration. This makes the use of low CN oxygen fuels an interesting route to improve the applicability of PCCI combustion in diesel engines. In earlier studies, performed on a heavy-duty engine, cyclic oxygenates were found to consistently outperform their straight and branched counterparts with respect to curbing soot. This was attributed to a considerably lower CN.

Premixed combustion modes in compression ignition engines are studied as a promising solution to meet fuel economy and increasingly stringent emissions regulations. Nevertheless, PCCI combustion systems are not yet consolidated enough for practical applications. The high complexity of such combustion systems in terms of both air-fuel charge preparation and combustion process control requires the employment of robust and reliable numerical tools to provide adequate comprehension of the phenomena. Object of this work is the development and validation of suitable models to evaluate the effects of charge premixing levels in diesel combustion. This activity was performed using the Lib-ICE code, which is a set of applications and libraries for IC engine simulations developed using the OpenFOAM® technology.

The present paper describes the results of a cooperative research project between GM Powertrain Europe and Istituto Motori - CNR aimed at studying the impact of both fresh and highly oxidized Rapeseed Methyl Ester (RME) at different levels of blending on performance, emissions and fuel consumption of modern automotive diesel engines featuring Closed-Loop Combustion Control (CLCC). In parallel, the capability of this system to detect the level of biodiesel blending through the use of specific detection algorithms was assessed. The tests were performed on the recently released 2.0L Euro5 GM diesel engine for passenger car application equipped with embedded pressure sensors in the glow plugs. Various blends of fresh and aged RME with reference diesel fuel were tested, notably 20% RME by volume (B20), 50% (B50) and pure RME (B100).

The present paper describes some results of a cooperative research project between GM Powertrain Europe and Istituto Motori of CNR aimed at studying the impact of FAME and GTL fuel blends on the performance, emissions and fuel consumption of the latest-generation automotive diesel engines. The investigation was carried out on the newly released GM 2.0L 4-cylinder “torque-controlled” Euro 5 diesel engine for PC application and followed previous tests on its Euro 4 version, in order to track the interaction between the alternative fuels and the diesel engine, as the technology evolves. Various blends of first generation biodiesels (RME, SME) and GTL with a reference diesel fuel were tested, notably B20, B50 and B100. The tests were done in a wide range of engine operation points for the complete characterization of the biodiesels performance in the NEDC cycle, as well as in full load conditions.

When increasing EGR from low levels to a level that corresponds to low temperature combustion, soot emissions initially increase due to lower soot oxidation before decreasing to almost zero due to very low soot formation. At the EGR level where soot emissions start to increase, the NOx emissions are low, but not sufficiently low to comply with future emission standards and at the EGR level where low temperature combustion occurs CO and HC emissions are too high. The purpose of this study was to investigate the possibilities for shifting the so-called soot bump (where soot levels are increased) to higher EGR levels, or to reduce the magnitude of the soot bump using very high injection pressures (up to 240 MPa) while reducing the NOx emissions using EGR. The possibility of reducing the CO and HC emissions at high EGR levels due to the increased mixing caused by higher injection pressure was also investigated and the flame was visualized using an endoscope at chosen EGR values.

It has been previously shown that engine-out soot emissions can be reduced by using Fischer-Tropsch (FT) fuels, due to their lack of aromatics, compared to conventional Diesel fuels. In this investigation the engine-out emissions and fuel consumption parameters of an FT fuel derived from natural gas were compared to those of Swedish low sulfur diesel (MK1) when used in Low Temperature Combustion mode in a single cylinder heavy-duty diesel engine. The effects of varying Needle Opening Pressure (NOP), Charge Air Pressure (CAP) and Exhaust Gas Recirculation (EGR) according to an experimental design on the measured variables were also assessed. CAP and EGR were found to be the most significant factors for the combustion and emission parameters of both fuels. Increases in CAP resulted in lower soot emissions due to enhanced charge mixing, however NOx emissions rose as CAP increased.

Soot formation and oxidation are complex and competing processes during diesel combustion. The balance between the two processes and their history determines engine-out soot values. Besides the efforts to lower soot formation with measures to influence the flame lift-off distance for example or to use HCCI-combustion, enhancement of late soot oxidation is of equal importance for low-λ diffusion-controlled low emissions combustion with EGR. The purpose of this study is to investigate soot oxidation in a heavy duty diesel engine by statistical analysis of engine data and in-cylinder endoscopic high speed photography together with CFD simulations with a main focus on large scale in-cylinder gas motion. Results from CFD simulations using a detailed soot model were used to reveal details about the soot oxidation.

The purpose of the investigation presented here was to compare the effects of fuel composition on combustion parameters, emissions and fuel consumption in engine tests and simulations with five fuels: a Diesel-water emulsion, a Diesel-ethanol blend, a Diesel-ethanol blend with EHN (cetane number improver), a Fischer-Tropsch Diesel and an ultra-low sulfur content Diesel. The engine used in the experiments was a light duty, single cylinder, direct injection, common rail Diesel engine equipped with a cylinder head and piston from a Volvo NED5 engine. In tests with each fuel the engine was operated at two load points (3 bar IMEP and 10 bar IMEP), and a pilot-main fuel injection strategy was applied under both load conditions. Data were also obtained from 3-D CFD simulations, using the KIVA code, to compare to the experimental results and to further analyze the effects of water and ethanol on combustion.

Future demands for improvements in the fuel economy of gasoline passenger car engines will require the development and implementation of advanced combustion strategies, to replace, or combine with the conventional spark ignition strategy. One possible strategy is homogeneous charge compression ignition (HCCI) achieved using negative valve overlap (NVO). However, several issues need to be addressed before this combustion strategy can be fully implemented in a production vehicle, one being to increase the upper load limit. One constraint at high loads is the combustion becoming too rapid, leading to excessive pressure-rise rates and large pressure fluctuations (ringing), causing noise. In this work, efforts were made to reduce these pressure fluctuations by using a late injection during the later part of the compression. A more appropriate acronym than HCCI for such combustion is SCCI (Stratified Charge Compression Ignition).